SpecificationsWingspan: 58 in (1475mm)Length: 37 in (940mm)Wing Area: 525 sq in (33.7 sq dm)Weight w/o Battery: 32–35 oz (910–1000 g)Weight w/Batt
10 E-flite Apprentice Assembly Manual 3. Locate the main gear and press it into the slot in the fuselage that is behind the battery compartment on t
11E-flite Apprentice Assembly ManualWing InstallationRequired PartsWing panel (right and left) Wing cover, frontWing cover, rear Rubber band (8)Fuse
12 E-flite Apprentice Assembly Manual 4. Make sure the two wing panels are pressed tightly together with no gap between them. Position the front win
13E-flite Apprentice Assembly Manual 7. Connect the aileron pushrod clevis to the aileron control horn in the hole that is farthest away from the ai
14 E-flite Apprentice Assembly Manual 11. Install the last four rubber bands using the Steps 9 and 10 as a guide. You will install two across (as in
15E-flite Apprentice Assembly Manual 2. Open the hatch from the rear of the fuselage as shown. The front of the hatch is hinged so it will not detac
16 E-flite Apprentice Assembly ManualInstalling the Transmitter BatteriesRequired PartsTransmitter AA battery (4) 1. Check to make sure the transmi
17E-flite Apprentice Assembly Manual 5. Slide the battery cover back into position on the back of the transmitter.Note: The installation of the batt
18 E-flite Apprentice Assembly Manual 2. Use an adjustable wrench to remove the nut from the propeller adapter. Set the nut aside so it does not get
19E-flite Apprentice Assembly Manual 5. Slide the propeller from the propeller adapter. The installation of the propeller is the reverse of the prev
2 E-flite Apprentice Assembly ManualIntroductionThe E-flite® Apprentice RTF is a 15-size high wing trainer, constructed of lightweight, durable Z-Foam
20 E-flite Apprentice Assembly ManualThrottle/Rudder StickElevator/Aileron StickReversing SwitchesMix Switch (not used for Apprentice)Throttle TrimRud
21E-flite Apprentice Assembly Manual 2. Plug the EC3 connector on the flight battery into the speed control. You will hear a series of beeps or tone
22 E-flite Apprentice Assembly Manual 4. Check the movement of the elevator with the radio system. Pulling the elevator/aileron stick (right stick o
23E-flite Apprentice Assembly ManualChecking the Elevator (Mode 1) 3. Center the elevator stick. This is the left stick on the transmitter. The elev
24 E-flite Apprentice Assembly Manual 5. Check the movement of the elevator with the radio system. Pushing the elevator/rudder stick forward will ma
25E-flite Apprentice Assembly Manual 7. Check the movement of the rudder using the transmitter. When the rudder/throttle stick (left side of the tr
26 E-flite Apprentice Assembly ManualChecking the Steering Trim (Mode 1 and 2)Note: Checking the steering trim must be done after the aircraft has bee
27E-flite Apprentice Assembly ManualChecking the Ailerons (Mode 1 and 2) 10. Center the aileron stick. Thread the clevis in or out on the aileron pu
28 E-flite Apprentice Assembly Manual 12. Check the movement of the aileron using the transmitter. When the aileron/elevator stick (Mode 2 transmitt
29E-flite Apprentice Assembly Manual 13. This completes the radio setup section. You may now power down your airplane and transmitter. To do this fo
3E-flite Apprentice Assembly ManualContents of Kit/Parts LayoutEFL2726 Wing SetEFL2727 FuselageEFL2728 Tail SetEFL2729 CowlEFL2730 Pushrod SetEFL
30 E-flite Apprentice Assembly ManualApprentice Balanced - No Correction NeededApprentice Nose Heavy -Add Weight to Tail or Move Battery RearwardAppre
31E-flite Apprentice Assembly Manual 3. You should have total control of the model with the trainer switch pulled at 30 paces (90 feet).30 paces (90
32 E-flite Apprentice Assembly ManualSetting the Control ThrowsRequired PartsAssembled airframe Charged flight batteryTransmitterRequired Tools and A
33E-flite Apprentice Assembly Manual 2. Plug the motor battery into the speed control. Important: Always use extreme caution around the propeller wh
34 E-flite Apprentice Assembly ManualRudder Throw 4. Use a ruler to check the control throws on your rudder. The dimensions are shown below. For you
35E-flite Apprentice Assembly Manual 6. Once all the control throws have been set, make sure to slide the clevis retainers over the clevises to prev
36 E-flite Apprentice Assembly Manual 2. Slide the spinner backplate on the propeller adapter. 3. Install the washer on the propeller shaft. 4.
37E-flite Apprentice Assembly Manual 5. Snap the spinner cone on the spinner backplate. It should snap on the backplate using a little force.Warning
38 E-flite Apprentice Assembly ManualOptional Items for Your ApprenticeAs you have selected the world of electric power to begin your RC experience, w
39E-flite Apprentice Assembly ManualLiPo Battery Pack InformationWarning!Lithium Polymer (LiPo) batteries are significantly more volatile than other r
4 E-flite Apprentice Assembly ManualCharging the Flight BatteryYour Apprentice can be ready to fly in as little time as it takes to charge the flight
40 E-flite Apprentice Assembly Manual• Lithiumbatteriescanstilligniteafteratleast45minutes due to a delayed chemical reaction. If battery is
41E-flite Apprentice Assembly ManualBasic Disposal InstructionsBefore discarding any LiPo battery it must be rendered safe. The following steps must b
42 E-flite Apprentice Assembly ManualDamage LimitsHORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODU
43E-flite Apprentice Assembly ManualIf you choose to pay by credit card, please include your credit card number and expiration date. Any repair left u
44 E-flite Apprentice Assembly Manual2008 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanctioned e
45E-flite Apprentice Assembly ManualBuilding and Flying Notes
46 E-flite Apprentice Assembly ManualBuilding and Flying Notes
47E-flite Apprentice Assembly ManualBuilding and Flying Notes
13464.1© 2008 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 1 877 504 0233 horizonhobby.com E-fliteRC.com
5E-flite Apprentice Assembly Manual 2. Select the proper number of cells that you will be charging. Your Apprentice includes a 3-cell flight pack, s
6 E-flite Apprentice Assembly Manual 5. Push the start button to begin the charging process. Once this is done, the charger will make an audible bee
7E-flite Apprentice Assembly Manual 2. Slide the pins on the bottom of the fin through the holes of the stabilizer and into those in the fuselage. M
8 E-flite Apprentice Assembly Manual 4. Connect the elevator pushrod clevis to the elevator control horn in the hole that is farthest away from the
9E-flite Apprentice Assembly ManualLanding Gear InstallationRequired PartsFuselage Assembly Nose gear w/wheelMain gear w/wheelsRequired ToolsPhillips
Commentaires sur ces manuels