E-flite Control Line Motor Timer Manuel d'utilisateur télécharger pdf

Multiple-Function Electronic Timer

EFLA172

The E-flite C/L Timer has been designed to deliver control of an R/C ESC for use in an electric control line model. The

timer has a very low weight of only 3.2 grams and is very compact in size. The timer is programmable and has a second

function for controlling other features on your model such as retractable landing gear. The main features of the C/L

Timer are listed below:

1. Programmable timer settings in 1 minute increments

2. Motor rpm is adjustable from off to full throttle

3. Motor cut-off alert in flight

4. Gradual motor rpm slow down prior to cut off

5. Optional control for items like retractable landing gear

6. quick and easy stopping control

Introduction of Use

The top of the timer has the start button and Motor RPM adjustment knob. The label is located on the bottom of the

timer.

You will note the label is on the bottom of the timer. On the left side there are two sets of pins. These pins are for the

ESC and second function. Please note the labeling of the ground wire, positive wire, and signal wire on the left side of

the timer. This labeling is correct when viewed from the bottom of the timer. The ESC port is on the top of the timer

and the Optional control is for retract servos, etc. This is the port that is on the bottom of the timer.

In the middle of the label we show the Motor RPM potentiometer. This potentiometer is located on the opposite side of

the timer. To increase motor RPM you turn the knob clockwise. To decrease motor RPM you turn the knob counter-

clockwise. Please note that if you turn the knob fully counter-clockwise the motor will not run.

On the right hand side of the label we show the Start button. This button is located on the top of the timer. This button

controls the duration of flight as well as the emergency stop ability of the timer.

Battery power required for timer operation must exceed 5 volts as a minimum voltage.

Istructions for Use

Plugging in the ESC and optional device

1. Plug the ESC into the timer ensuring to align the ground and signal wires. The ground wire is usually brown

or black. The signal wire is usually orange or white. If you plug the ESC in backwards, the unit will fail to

operate. You will want to plug the ESC onto the top of the timer.

2. Plug the retract servo into the timer ensuring to align the ground and signal wires. This will plug into the

lower set of pins on the timer, or under the ESC.

3. If using the optional device (designed for retract operation) you will find the retracts to raise 15 seconds after

the motor begins to run. The retracts will lower 18 seconds before the cut-off warning occurs.

Setting timing for flight

1 2 3 4 5

Résumé du contenu

Page 1 - Istructions for Use

Multiple-Function Electronic Timer EFLA172 The E-flite C/L Timer has been designed to deliver control of an R/C ESC for use in an electric control li

Page 2

1. Pushing the start button and holding it down will cause the motor to run for a split second at minimal throttle. As you continue to hold the sta

Page 3

discretion of Horizon. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use,

Page 4

Warranty Inspection and Repairs To receive warranty service, you must include your original sales receipt verifying the proof-of-purchase date. Provid

Page 5

equipment by handing it over to as designated collection point for the recycling of waste electrical and electronic equipment. The separate collection

Commentaires sur ces manuels

Pas de commentaire

E-flite Control Line Motor Timer Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel E-flite Control Line Motor Timer. E-flite Control Line Motor Timer User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel E-flite Control Line Motor Timer