SpecificationsWingspan: 38 in (960mm)Length: 41 in (1045mm)Wing Area: 473.5 sq in (30.5 sq dm)Weight w/o Battery: 34–36 oz (965–1020 g)Weight w/Ba
10 E-flite Ultimate 20-300 Assembly ManualAileron Servo InstallationRequired PartsTop wing Bottom wingControl horn (2) Interconnect horn (4)Aileron
11E-flite Ultimate 20-300 Assembly Manual 2. Use a hobby knife to trim the covering from the slot in the aileron. Leave the covering on the top f
12 E-flite Ultimate 20-300 Assembly Manual 6. Use the string to pull the extension through the hole at the center of the bottom wing.Hint: Use low-
13E-flite Ultimate 20-300 Assembly Manual 9. Repeat Steps 1 through 8 for remaining control horns and servo. 10. Use a pin drill and 1/16-inch (
14 E-flite Ultimate 20-300 Assembly Manual 13. Slide the lightweight screw lock connector into the hole drilled back in Step 10. 14. Use the con
15E-flite Ultimate 20-300 Assembly ManualNote: The servo horn should be installed parallel to the hinge line to produce the correct linkage geometry.I
16 E-flite Ultimate 20-300 Assembly Manual 2. Slide the stabilizer into the slot at the rear of the fuselage. Slide the stabilizer forward, then ali
17E-flite Ultimate 20-300 Assembly Manual 5. Once aligned, use a felt-tipped pen to trace the outline of the fuselage onto the top and bottom of the
18 E-flite Ultimate 20-300 Assembly Manual 7. Slide the elevator joiner wire into the slot for the stabilizer before gluing the stabilizer into posi
19E-flite Ultimate 20-300 Assembly ManualHinging the Rudder and StabilizerRequired PartsElevator (left and right) RudderTail wheel assembly Fuselage
2 E-flite Ultimate 20-300 Assembly ManualIntroductionE-flite's Ultimate 20-300 10 ARF is a sport replica of the rare two-place aerobatic aircraft
20 E-flite Ultimate 20-300 Assembly Manual 4. Slide the hinges in the slots in the stabilizer. 5. Repeat Steps 1 through 4 to position the remain
21E-flite Ultimate 20-300 Assembly Manual 9. Use medium CA to glue the tail wheel assembly into the slot at the bottom of the rudder. 10. Mark fou
22 E-flite Ultimate 20-300 Assembly ManualRudder and Elevator Servo InstallationRequired PartsFuselage Servo (2)Control horn Silicone clevis retaine
23E-flite Ultimate 20-300 Assembly ManualHint: Use a piece of string or some tape to secure the two plugs together so that they cannot pull apart insi
24 E-flite Ultimate 20-300 Assembly Manual 7. Secure the link using a 2mmx 4mm machine screw and a #1 Phillips screwdriver. 8. Repeat Steps 2 throu
25E-flite Ultimate 20-300 Assembly Manual 2. Use four 4-40 x 1/2-inch socket head screws and four #4 washers to attach the main landing gear to th
26 E-flite Ultimate 20-300 Assembly Manual 2. Attach the motor to the firewall using four 4-40 x 3/8-inch socket head screws and four #4 washers. Ti
27E-flite Ultimate 20-300 Assembly Manual 5. Secure a small square of hook and loop material inside the fuselage. This is done to keep the strap tha
28 E-flite Ultimate 20-300 Assembly ManualImportant Information About Your PropellerIt is also very important to check to be sure the propeller is bal
29E-flite Ultimate 20-300 Assembly ManualUpper Wing and Canopy InstallationRequired PartsFuselage Top wingBottom wing Canopy2mm nut (2) 2mm washer
3E-flite Ultimate 20-300 Assembly ManualContents of Kit/Parts LayoutReplacement PartsEFL2751 FuselageEFL2752 Top Wing w/Ailerons, Left and RightEFL2
30 E-flite Ultimate 20-300 Assembly Manual 3. Use a pin drill and 1/16-inch (1.5mm) drill bit to poke the covering to access the screw holes for the
31E-flite Ultimate 20-300 Assembly Manual 6. With the bottom wing installed, attach the top wing to the cabane struts using four 2mm washers, two 2m
32 E-flite Ultimate 20-300 Assembly Manual 10. Position both ailerons in their neutral positions. Use a 2mm x 6mm machine screw and #1 Phillips scr
33E-flite Ultimate 20-300 Assembly ManualControl Horn LengthThis length is also very critical. The closer the pushrod attachment is to the surface the
34 E-flite Ultimate 20-300 Assembly ManualProgrammer Servo ThrowsAileronsUp 11/16-inch (16mm)Down 9/16-inch (13mm)ElevatorUp 2-inch (50mm)Down 2-i
35E-flite Ultimate 20-300 Assembly ManualCenter of GravityAn important part of preparing the aircraft for flight is properly balancing the model.Cauti
36 E-flite Ultimate 20-300 Assembly ManualRange Test Your Radio 1. Before each flying session, be sure to range check your radio. This is accomplish
37E-flite Ultimate 20-300 Assembly Manual2008 Official AMA National Model Aircraft Safety CodeGENERAL1) I will not fly my model aircraft in sanction
38 E-flite Ultimate 20-300 Assembly ManualBuilding and Flying Notes
39E-flite Ultimate 20-300 Assembly ManualBuilding and Flying Notes
4 E-flite Ultimate 20-300 Assembly ManualRequired Tools and AdhesivesTools & EquipmentFelt-tipped pen Ball driver: 3/32-inchLow-tack masking tape
13465© 2008 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com E-fliteRC.com
5E-flite Ultimate 20-300 Assembly ManualWarranty InformationWarranty PeriodHorizon Hobby, Inc., (Horizon) warranties that the Products purchased (the
6 E-flite Ultimate 20-300 Assembly ManualQuestions, Assistance, and RepairsYour local hobby store and/or place of purchase cannot provide warranty sup
7E-flite Ultimate 20-300 Assembly ManualSafety, Precautions, and WarningsAs the user of this product, you are solely responsible for operating it in a
8 E-flite Ultimate 20-300 Assembly Manual 3. Position the hinges in the pre-cut slots in the aileron. Slide the hinges into the aileron up to the
9E-flite Ultimate 20-300 Assembly ManualNote: If the control surface is tight against the main surface, it will limit the amount of control throw the
Commentaires sur ces manuels