E-flite Park 400 Brushless Inrunner Motor, 4200Kv Manuel d'utilisateur télécharger pdf

Park 370 & Park 400 Inrunner Brushless Motor Instructions

Park 370 Brushless Motor Features:

• Upgrade for your Speed 280 and Speed 370 applications

• Excellent Motor for small airplanes between 10 oz – 14 oz (280 g – 400 g)

• Adapter plate included for mounting to GWS and E-flite style gearboxes

• Prop adapter and gold-plated connectors included

• Slotless 2-pole design

Park 370 Specifications

Diameter: 20mm (.80 in.)

Case Length: 30mm (1.2 in.)

Weight (no gearbox): 48g (1.7 oz.)

Shaft Diameter: 2mm (.08 in)

EFLM1000 EFLM1005 EFLM1010

Kv: 4100 (rpms per volt) Kv: 5400 (rpms per volt) Kv: 3600 (rpms per volt)

Io: 1A @10V (no load current) Io: 1.3A @10V (no load current) Io: .8A @10V (no load current)

Ri: .1ohms (resistance) Ri: .12ohms (resistance) Ri: .29 ohms (resistance)

Continuous Current: 8A* Continuous Current: 10A* Continuous Current: 7A*

Max Burst Current: 13A* Max Burst Current: 15A* Max Burst Current: 11A*

Cells: 6-10 NiCd/NiMh or 2-3 Li-Po Cells: 4-8 NiCd/NiMh or 2 Li-Po Cells: 6-10 NiCd/NiMh or 2-3 Li-Po

Recommended Gearbox: 6.6:1 Recommended Gearbox: 5.33:1 or 6.6:1 Recommended Gearbox: 5.33:1

Recommended Props: 9x6 to 12x6 Recommended Props: 9x4.7 to 12x6 Recommended Props: 9x4.7 to 11x4.7

Brushless ESC: 10- to 25-Amp (EFLA311) Brushless ESC: 10- to 25-Amp (EFLA311) Brushless ESC: 10- to 25-Amp (EFLA311)

Includes: 10T & 12T Pinion Gears Includes: 10T & 12T Pinion Gears Includes: 10T & 12T Pinion Gears

E-flite Plane: Tribute, Ultimate, Yak54F E-flite Plane: none recommended E-flite Plane: Gypsy

Park 400 Brushless Motor Features:

• Upgrade for your Speed 400 applications

• Excellent motor for small airplanes between 12 oz – 26 oz (340 g – 740 g)

• Adapter plate included for mounting to GWS and E-flite style gearboxes

• Prop adapter and gold-plated connectors included

• Slotless 2-pole design

Park 400 Specifications

Diameter: 20mm (.80 in.)

Case Length: 40mm (1.6 in.)

Weight (no gearbox): 68 g (2.4 oz)

Shaft Diameter: 2mm (.08 in)

EFLM1100 EFLM1105

Kv: 4200 (rpms per volt) Kv: 3700 (rpms per volt)

Io: 1.8A @ 10V (no load current) Io: .8A @10V (no load current)

Ri: .24 ohms (resistance) Ri: .11 ohms (resistance)

Continuous Current: 18A* Continuous Current: 15A*

Max Burst Current: 24A* Max Burst Current: 20A*

Cells: 6-10 NiCd/NiMh or 2-3 Li-Po Cells: 6-10 NiCd/NiMh or 2-3 Li-Po

Recommended Gearbox: 6.6:1 Recommended Gearbox: 5.33:1 or 6.6:1

Recommended Props: 10x4.7 to 12x6 Recommended Props: 9x7 to 12x6

Brushless ESC: 20- to 25-Amp (EFLA311) Brushless ESC: 20- to 25-Amp (EFLA311)

Includes: 10T & 12T Pinion Gears Includes: 10T & 12T Pinion Gears

E-flite Plane: Mini Funtana, Mini Edge E-flite Plane: Mini Funtana, Mini Edge

* Maximum Operating Temperature: 220 degrees Fahrenheit

* Adequate cooling is required for all motor operation at maximum current levels.

* Maximum Burst Current duration is 5 seconds. Adequate time between maximum burst intervals is required.

Installation of Pinion Gear & Gearbox:

For your convenience, this motor includes both a 10 Tooth and a 12 Tooth pinion gear. It will be necessary for you to install the pinion on the shaft. In some E-flite airplanes,

a pinion gear is also included with the included gearbox. E-flite recommends you use the pinion gear included with your gearbox for the best set-up.

The 10 Tooth pinion is for use with an E-flite (EFLM221) or GWS ‘D’ gearbox with 6.6:1 gear ratios. A gearbox with a 6.6:1 ratio has a 66 Tooth spur gear on the gearbox and

the motor uses a 10 Tooth pinion gear installed on the shaft. The 12 Tooth pinion is for use with an E-flite (EFLM216) or GWS ‘C’ gearbox with 5.33:1 gear ratios. A gearbox

with a 5.33:1 ratio has a 64 Tooth spur gear on the gearbox and the motor uses a 12 Tooth pinion gear installed on the shaft. The E-flite spur gears are a .4 module.

When installing motors into the E-flite gearbox, it is very important that your gear mesh is correct and the gear’s mesh is smooth with no binding. The E-flite gearbox features

adjustable slotted mounting holes so that you can ensure your gear mesh is correct. Remember, if your mesh is too loose or too tight, it may strip the gears. One suggestion

may be to insert the polybag included with the motor or a small piece of paper in between the pinion and spur gear as you are installing them. Tighten and secure the screws

to the gearbox. Always make sure the screws are long enough so they have properly seated into the motor. You can easily pull the polybag or paper out by rotating the shaft

until it comes out. Be certain to check the mesh at multiple points on the spur gear before finalizing the motor mounting position in the gearbox. To extend the life of your

gearbox, we also recommend using a small amount of grease, such as lithium grease, on the spur gear.

Once a pinion is installed on the shaft, it will be necessary to remove the pinion from the motor shaft if you want to use the motor with a different gearbox than the ones

specified above. The gear mesh will bind and the motor will not operate properly if you have incorrect gear ratios. We recommend using a gear puller for this step for the

safest removal of the pinion gear. Never reuse a pinion gear that has been removed from a shaft.

1 2

Résumé du contenu

Page 1

Park 370 & Park 400 Inrunner Brushless Motor Instructions Park 370 Brushless Motor Features: • Upgrade for your Speed 280 and Speed 370 applica

Page 2

Installing Pinion Gear 1. Align pinion on end of shaft and press fit using a vise for proper installation. 2. Support the aft bearing and shaft using

Commentaires sur ces manuels

Pas de commentaire

E-flite Park 400 Brushless Inrunner Motor, 4200Kv Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel E-flite Park 400 Brushless Inrunner Motor, 4200Kv. E-flite Park 400 Brushless Inrunner Motor, 4200Kv User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel E-flite Park 400 Brushless Inrunner Motor, 4200Kv