Pulse XT 25e ARFAssembly Manual
10Ο Ο 6. Attach the clevises to the control horn on the elevator at the third holefrom the mounting surface, and on the rudder at the second hole from
Receiver InstallationRequired PartsFuselageSpektrum AR6200 ReceiverAdhesive backed hook and loop tapeΟ 1. Install the main and satellite receiver in t
12Ο 2. Using a 3/32” balldriver, install the motor on the firewall with four 4-40x 1/2" socket head bolts. The motor wires should exit towards th
Motor and Battery Installation E-flite Power 32Required PartsE-flite Power 32 Motor with hardwareE-flite 60A ESCE-flite BatteryPropeller(4) 4-40 x 3/4
14Ο 5. Install the ESC on the right-hand side of the battery compartment withhook and loop tape. The battery leads, switch leads and throttle leads wi
Cowling, Propeller and Spinner InstallationRequired PartsFuselageCowling(4) 4-40 x 1/4" socket head bolts(4) #4 steel washersSpinner with screwsP
16Ο 4. Install the spinner cone using a #1 Philips screwdriver and the suppliedPhilips head screws.An alternate method to drilling completely through
Wing JoiningRequired PartsWing halves (L and R)(2) dihedral joiners(2) leading edge dowels(2) 6-32 x 1” socket head bolts(2) #6 steel washersRequired
18Ο 4. Apply low-tack tape to the upper and lower surfaces of the center of thewing panels as shown. This will allow for easy clean up of any excess g
Ο 8. Install the dihedral joiners in one wing slot and slide the other wing panelonto the joiner. Wipe off any excess epoxy that squeezes out of the j
Table of ContentsIntroduction... 2Specifications...
20Ο 2. A string is provided in each wing half to draw the aileron lead throughthe wing. Attach the end of the string to the aileron servo lead and pul
Ο Ο 7. Prepare each of the 4-3/4” long aileron pushrods with a clevis andsilicone keeper.Ο Ο 8. Center the aileron servo using your radio or JR MatchM
22Canopy and Cooling Exit ScoopRequired PartsFuselageCanopyCooling Exit ScoopRequired Tools and AdhesivesLow-tack tapeCanopy GlueΟ 1. Trial fit the ca
Optional Float Installation.Required parts:E-flite fiberglass 25-size Float SetSullivan 36” flex cablePulse XT 25e (assembled)(4) 1/8” float mount spa
24Ο Ο 4. Use a file or rotary tool to make a 1/4” wide flat on the top of each ofthe four axles. The flat should be located approximately 9/16” (14mm)
Ο 7. Install the rudder assembly, steering arm and pushrod connector on thenylon bracket. Refer to pages 12 and 13 in the Float Set assembly manual fo
26Ο 11. Use the two remaining full brass straps to attach the pushrod tube to theleft side of the Pulse fuselage. Locate the straps as shown in the pi
Flight PreparationControl Directions1. Connect the throttle lead from the ESC to the receiver.2. Connect the wing servos to the receiver with two 3” e
28Center of Gravity (CG)The recommended center of gravity range for the Pulse XT 25e is 2.5 - 3.0”(63 - 76mm) behind the leading edge of the wing. Bef
Optional Items25-Size Float SetE-flite quick-mount floats are designed specifically for 25-size airplanes thatare float-ready out of the box, so you c
Using This ManualThis manual is divided into sections to make assembly of the model easier tounderstand and to provide breaks between each major secti
30E-flite Power MeterThe E-flite Power Meter is designed for inline monitoring of Volts, Amps, Watts,and Capacity, based on the mode you select to dis
Lithium Polymer Battery Pack InformationLithium Polymer (LiPo) batteries are significantly more volatile than otherrechargeable batteries used in RC a
32Crash DamageIf there are signs of smoke or overheating, DO NOT go near the battery orequipment until it has been observed from a safe distance for a
AMA National Model Aircraft Safety CodeGENERAL 1. A model aircraft shall be defined as a non-human-carrying device capableof sustained flight in the a
Warranty Period:Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that theProducts purchased (the "Product") will be free from d
Inspection or RepairsIf this Product needs to be inspected or repaired, please call for a ReturnMerchandise Authorization (RMA). Pack the Product secu
© 2008 Horizon Hobby, Inc.4105 Fieldstone RoadChampaign, Illinois 61822(877) 504-0233horizonhobby.comE-fliteRC.com
Required EquipmentRadioYou will need a minimum of a 4-channel radio for this model. A completeradio system can be purchased or, if you have a suitable
Landing Gear Assembly and InstallationRequired parts:FuselageMain landing gear (wheels installed)Wheel pants(2) 6-32 x 1/2" socket head bolts(2)
6Ο Ο 4. Using a 1/16 in (1.5mm) drill bit in a pin drill, drill two holes wheremarked on the wheel pant. Apply a drop of thin CA in each hole to stren
Ο 2. Slide the vertical stabilizer into place. It will be necessary to deflect therudder to the right in order for the rudder horn to clear the elevat
8Fuselage Servo InstallationRequired Items(2) Servos and hardware(2) 23 5/8” rudder and elevator pushrods(2) nylon clevises and silicone keepers(2) pu
Ο Ο 4. Remove the servo arm using a #1 philips screwdriver. Using sidecutters,trim three of the arms from a standard four arm servo horn, leaving one
Commentaires sur ces manuels